Millipore - Product Module

Aervent–50 Disposable Filters with Hydrophobic Aervent Membrane

Description
Aervent-50 0.2 µm hydrophobic filters contain a 50 mm Aervent PTFE membrane in a bi-directionally supported polypropylene casing. This sterilizing-grade filter is designed for critical small scale gas line and air venting applications. The hydrophobic Aervent PTFE membrane provides high flow rates and throughput, low extractables and particle shedding, and broad chemical compatibility.

For traceability and easy identification, each Aervent-50 filter is hot stamped with its catalogue number and lot number. Each Aervent-50 filter is integrity tested during manufacture.

Typical Applications
- Sterile venting of vessels and carboys
- Autoclave vacuum break lines
- Low volume sterile filtration of non- aqueous fluids
- Small fermenter inlet and exhaust gas filtration

Specifications (return to top)

Materials of Construction
Housing
Polypropylene
Filter
PTFE
Filtration Area, cm²
19.6
Maximum Inlet Pressure, bar (psig)
4.1 (60) @ 25 °C
Bacterial Retention
Quantitative retention of 10⁷ CFU/cm² Brevundimonas diminuta (ATCC^® 19146) per ASTM F838-83 methodology
Bacterial Endotoxins
<0.5 EU/mL as determined by the LAL test
Gravimetric Extractables
≤1.0 mg in 70//30 % IPA/water
Sterilization
10 autoclave cycles of 30 min @ 130 °C; not in-line steam sterilizable
Integrity Test - Bubble Point
≥1100 mbar (16 psig) with 60//40 % IPA/water

Typical Air Flow Rate

Aervent-50 (MTGR 050) Air Flow Rate

Compare	Catalogue No.	Connections, Inlet/Outlet	Diameter, cm (in)	Length, cm (in)
	MTGR05010	Hose for 4 to 9.5 mm I.D. latex tubing and Female Luer slip	6.2 (2.4)	7.1 (2.8)	» Add to Cart
	MTGR15010	19 mm (3/4 in.) Sanitary Flange	6.2 (2.4)	5.5 (2.16)	» Add to Cart
	MTGR55010	One side: 3 mm (1/8 in.) NPTM. Other side: Hose for 4 to 9.5 mm I.D. latex tubing and Female Luer slip	6.2 (2.4)	6.4 (2.52)	» Add to Cart
	MTGR65010	One side: 3 mm (1/8 in.) NPTM. Other side: Hose for 6.5 to 9.5 mm I.D. silicone tubing	6.2 (2.4)	5.3 (2.1)	» Add to Cart
	MTGR75010	3 mm (1/8 in.) NPTM	6.2 (2.4)	5.7 (2.24)	» Add to Cart
	MTGR85010	Hose for 6.5 to 9.5 mm I.D. silicone tubing	6.2 (2.4)	7.2 (2.84)	» Add to Cart

Compare	Catalogue No.	Connections, Inlet/Outlet	Diameter, cm (in)	Length, cm (in)
	MTGR05000	Hose for 4 to 9.5 mm I.D. latex tubing and Female Luer slip	6.2 (2.4)	7.1 (2.8)	» Add to Cart
	MTGR15000	19 mm (3/4 in.) Sanitary Flange	6.2 (2.4)	5.5 (2.16)	» Add to Cart
	MTGR25000	One side: 19 mm (3/4 in.) Sanitary Flange. Other side: Hose for 4 to 9.5 mm I.D. latex tubing and Female Luer slip	6.2 (2.4)	6.3 (2.48)	» Add to Cart
	MTGR65000	One side: 3 mm (1/8 in.) NPTM. Other side: Hose for 6.5 to 9.5 mm I.D. silicone tubing	6.2 (2.4)	5.3 (2.1)	» Add to Cart
	MTGR75000	3 mm (1/8 in.) NPTM	6.2 (2.4)	5.7 (2.24)	» Add to Cart
	MTGR85000	Hose for 6.5 to 9.5 mm I.D. silicone tubing	6.2 (2.4)	7.2 (2.84)	» Add to Cart

Related Products (return to top)

		Optiseal Cartridge Filters with Hydrophobic Aervent Membrane Optiseal filters with Aervent membrane are designed for sterilizing applications, removing particles and microorganisms from gases and solvents. » Learn More...

		Opticap XL Disposable Capsule Filters with Hydrophobic Aervent Membrane The 0.2 µm hydrophobic Aervent^® polytetrafluoroethylene (PTFE) membrane provides sterility assurance, high flow rates and throughput. The Aervent membrane contributes to clean processes due its non-fiber releasing properties. » Learn More...

		Sterilizing-Grade Aervent Cartridge Filters The 0.2 µm hydrophobic Aervent^® polytetrafluoroethylene (PTFE) membrane provides sterility assurance, high flow rates and throughput. The Aervent membrane contributes to clean processes due its non-fiber releasing properties. » Learn More...

		Mobius Disposable Solutions Transform your process with Mobius flexible bioprocessing solutions from Millipore. » Learn More...